You are here: Home / Products / Hide / Alminum sheet / Bendable Aluminum Sheet

Product Category

Share to:

Bendable Aluminum Sheet

Bendable Aluminum Sheet
Alloy Series:1000,3000,5000,6000,7000
Temper: O,H14,H24,H32,H112
Thickness: 5-100mm, tolerance: +/-0.02mm
Width: 1000-1500mm, tolerance:+/-1mm
Length: 2000-6000mm, tolerance:+/-1mm
Surface: Mill finish,Anodized

Availability:

Quantity:


Inquire Add to Basket

Basic Information
Product Attributes
Supply Ability
Application
Packing

Bendable Aluminum Sheet is a rolled product with a rectangular cross section, a thickness of not less than 6.0mm (or 0.250 in), and a cut or sawn edge. It is produced in coils by a hot or cold rolling process and then cut to length. Aluminum thick plates can also be produced directly in straight lengths, depending on thickness.

Bendable Aluminum sheet Bendable Aluminum plate Sheet Aluminum Sheet H14

Alloy	Si	Fe	Cu	Mn	Mg	Cr	Ni	Zn		Ti	Zr	AL
1050	0.25	0.4	0.05	0.05	0.05	一	—	0.05	0.05V	0.03	—	99.5
1060	0.25	0.35	0.05	0.03	0.03	—	—	0.05	0.05V	0.03	—	99.6
1070	0.2	0.25	0.04	0.03	0.03	—	—	0.04	0.05V	0.03	—	99.7
1100	0.95Si+Fe		0.05~0.20	0.05	—	—	—	0.1	i	—	—	99
1200	1.00Si+Fe		0.05	0.05	—	—	—	0.1	—	0.05	—	99
3003	0.6	0.7	0.05~0.20	1.0~1.5	—	—	—	0.1	—	—	—	remainder
5052	0.25	0.4	0.4	0.1	2.2~2.8	0.15~0.35	—	0.1	—	----	—	Remainder
8011	0.50~0.9	0.6~1.0	0.1	0.2	0.05	0.05	—	0.1	—	----	—	Remainder

Alloy	Si	Fe	Cu	Mn	Mg	Cr	Ni	Zn		Ti	Zr	AL
1050	0.25	0.4	0.05	0.05	0.05	一	—	0.05	0.05V	0.03	—	99.5
1060	0.25	0.35	0.05	0.03	0.03	—	—	0.05	0.05V	0.03	—	99.6
1070	0.2	0.25	0.04	0.03	0.03	—	—	0.04	0.05V	0.03	—	99.7
1100	0.95Si+Fe		0.05~0.20	0.05	—	—	—	0.1	i	—	—	99
1200	1.00Si+Fe		0.05	0.05	—	—	—	0.1	—	0.05	—	99
3003	0.6	0.7	0.05~0.20	1.0~1.5	—	—	—	0.1	—	—	—	remainder
5052	0.25	0.4	0.4	0.1	2.2~2.8	0.15~0.35	—	0.1	—	----	—	Remainder
8011	0.50~0.9	0.6~1.0	0.1	0.2	0.05	0.05	—	0.1	—	----	—	Remainder

Product Category

Bendable Aluminum Sheet

WHAT WE PROVIDE

WHAT WE PROVIDE

ADDRESS

PHONE

WHAT WE PROVIDE